New Page 1
X-10 PHW04D Wireless Wall Switch With NO Wiring Needed
Put a Lightswitch Anywhere!
Upgrade with this decorative & powerful wall
switch
Have you ever wanted a light switch in a certain location,
but didn't want to rip a hole in a wall and connect electrical wires? Now X10 has come to
the rescue with the ALL NEW Ultra-slim Stick-a-Switch wireless wall switch! Easy single
push-button programming has your Stick-a-Switch set for each button to control a different
lamp or appliance!
- Lightweight,
sleek and slender designer style!
- Adheres to
any surface!
- Your dream
switch, in the perfect location!
- Control Up
To 3 Devices With Dimming Features, Or Appliance Modules Also, All X-10 Devices.
The Wireless RF Wall Switch works with either an X-1 0 PRO Security
System, such as the X-10 PR02000, or with a Transceiver Module PAT01, to provide remote
control of lights and appliances from anywhere in the house. It is designed to be mounted
in any location using either the supplied
double-sided
tape or Velcro.TM
PDF
Installation Instructions
Installation And Operating Instructions
The PHW04D works with the RF Base Transceiver (PAT01) or an X-1 0 PRO
Security Receiver (PR02000) giving you ON/OFF control of three individually coded X-1 0
PRO Modules and Brighten/Dim of lights connected to Lamp Modules or Wall Switch Modules.
In the default state (after first fitting the battery) the PHW04D is set to Housecode A.
The top three ON/OFF rocker keys control modules set to Unit Codes 1,2,3. The bottom
rocker key Brightens and Dims lights connected to Lamp and Wall Switch Modules.
Setup
1. Plug in an X10 PRO RF Base Transceiver (PAT01 sold separately).
2. To turn On/Off X10 PRO Modules set to Unit Codes 1,2, or 3 (on
Housecode A) press the Jeftor right side of the first, second or third rocker key. To
Brighten/Dim Lamp Modules or Wall Switch Modules press the Unit button first, then press
and hold the left or right side of the bottom rocker key.
3.Attach the PHW04D to awall using doublesided tape or Velcro .lf you want
to control Modules 1, 2 and 3 on Housecode A, you don't need to readany further.
To change the Housecode
Press and hold the first (top) ON rocker key.
The red LED flickers.
3 seconds later, the LED blinks the current setting: 1 blink for
Housecode A, 2 blinks for B 16 blinks for P.
· Release the first (top) ON rocker key.
· Press and release the first (top) ON rocker key the appropriate
number of times for the House Code you want to-set.
Once for A, twice for B, etc. The lED-blinks-for-each press.
IMPORTANT: Hold the button on your last press. 3 seconds later,
the red LED blinks back the new setting, e.g. 3 blinks for Housecode C. If you do not
follow this programming sequence, the LED will stay on for 1 second and your existing
setting will not be changed.
To change the Unit Code:
For the first (top) rocker key (the second and third rockers are always
one # higher than the first).
IE. If you set the first rocker key to 6, the second rocker key
controls 7, and the third control 8, etc..
Press and hold the top OFF rocker key. The red LED flickers. 3 seconds
later, the LED blinks the current setting: 1 blink for Unit Code 1, 2 blinks for 2, 16
blinks for 16.
Release the top OFF rocker key.
Press and release the top OFF rocker key the appropriate number of times
for the Unit Code you want. IMPORTANT: Hold the key on your last press. 3 seconds later
the new code blinks back. If you do not follow this programming sequence, the LED will
stay on for 1 second and your existing setting will not be changed.
To change battery:
Open battery holder on bottom of unit, and fit a CR2032 Lithium 3V
battery. Observe polarity.
Note: As with all RF transmitter
devices;electrical fields, metal doors and appliances can cause interference that can
decrease the strength of the transmitted signal. Reorienting the transmitter or receiver
console may increase your ability to send and receive the necessary signals.
| 
