Ademco 5883H Wireless Transceiver
The 5883H combines a 5881ENH Receiver and a 5800TM Transmission Module-making wirelessbi-directional installations faster and easier than ever before.
Compatible with all VISTA controls and 5800 wireless products
Not Compatible With:
4110
4110DL
4110XM
4110XMP
VIA-16
VISTA-20HW
VISTA-20HWSE
Installation Manual Click Here
Features:
OPERATING FREQUENCY: 345 MHZ
UL COMMERCIAL FIRE: Yes
Rated for Commercial Fire listing if dip switch #5 is enabled
HIGH-SECURITY ENCRYPTION Yes
DETAILS - Allows protection from code-grabbing where a codegrabber could receive the signal from a keyfob and retransmit to disarm the system later.For use with high-security encrypted devices. Limit of up to 16 encrypted devices. Dipswitch #1 must be enabled, and then can only be used with encrypted devices.MEMORY BUFFER 8 Events
DETAILS - Receiver buffer can hold 8events, if more than that come in at once, they might be lostUL COMMERCIAL BURG Yes
SPATIAL DIVERSITY SYSTEM Yes
DETAILS - Unique system designedto virtually eliminate the possibility of nulls and dead spotswith regard to Radio Frequency (RF) transmittersOPERATING TEMPERATURE
32F-122FDATE CODE LOCATION
DETAILS - The date code islocated on the circuit board pirnted in black ink. There is a letter which represents theyear and a three digit number which identifies the day. Example: If the stamped date codewas A002, this board was manufactured on January 2, 1998. G= 2004 F = 2003 E = 2002 D =2001 C = 2000 B = 1999 A = 1998 Z = 1997 Y = 1996 X = 1995TAMPER No
MOUNTING SPECIFICATIONS
DETAILS - The receiver can bemounted either in the can with the panel, in a seperate can, or remotely from the controlin its own surface mount plastic case. If mounting remotely, be sure to mount the receiverat least 10ft from the control or any keypad to avoid any interference from themicroprocessors in these units.. For best results, mount in a higher location than thetransmitters.ANTENNA
DETAILS - 2 vertical antennas, tobe mounted in right hand side of terminals.ADDRESSABLE KEYPADS Up To 16
DETAILS - The receiver willsupport up to 16 wireless keypads.5800 RF ZONE EXPANSION
Maximize panel's capacity.
DETAILS - The number of zones that the 5883H receiver can support depends onnumber of wireless zones the panel will support.ADDRESSABLE 0-7
DETAILS - Addressable for address0 thru 7 using dip switches 2-4. Also sets address for built-in TM module for 27-30.SIGNAL SENTRY
YES, Dip 5
DETAILS - When dip #5 is on, this enables thismode on the receiver. All the transmitters send 5 bursts of data when they check in.Normally a receiver must only receive one of these bursts. When the SignalSentry mode is enabled, the receiver drops to 1/2 strength after receiving the firstburst, and must receive a second burst at half strength, otherwise it disregards thatcheck in. It stays at half strength for a few seconds, then goes back to normal.SITE ID Yes
DETAILS - The Site ID number is aunique number that is factory programmed into each 5883. This number islearned into devices such as the 5839.OPERATING VOLTAGE 12VDC
BI-DIRECTIONAL WIRELESS Yes
DETAILS - Built in transmittermodule Set by dip switches The status of any one partition can be transmitted. The statuswill follow the partition assignment in device programming for the tm module. This appliesto control were the tm module is assigned in device programming to addresses 28,29,30 asan alpha console. NOTE: The Bi-directional portion of the 5839 does not utilize the builtin TM module. It uses the Site ID protocol. OPERATING CURRENT 80mA
RF JAM DETECTION Yes
DETAILS - This receiver candetect a condition that may impede proper RF reception if it is enabled in panelprogramming.DIMENSIONS
DETAILS - 7-3/8W x4-3/8H (10-7/8 w/antennas) x 1-7/16D, 188mm W x 112mm H (277mmw/antennas) x 37mm DPDF Manuals And Spec Sheets Below PopUps Must Be Allowed.
Installation Manual Click Here
CSFM LISTING Click Here
Wiring The Receiver Click Here
Mounting The Receiver Remotely Click Here
Mounting The Receiver Inside TheControl Panel Click Here
Mounting For Fire Applications Click Here
5800 Series Power Outputs Click Here
Wireless Overview Click Here
Removing RF Keypads
1. Remove power from thetransceiver. 2. Place Dip switch 1 in OFF(down) position, and Dip switch 8 inthe ON(up). 3. Power transceiver back up. 4. Observe the RED LED comes on andstays on. This is the LED to the right of the yellow LED in the center of the PCB. 5. Setdip switches 1 - 8 in their opposite position. 6. Return dip switches 1 - 8 back tostarting position. The RED LED will extinguish and all enrolled wireless keypads will beremoved from transceiver. 7. Remove power, set dip switch 8 back down. Make sure all dipsare in correct position before re-apply power. NOTE: When trying to enroll the site IDinto the keypad and is not learning in, check the red LED in top left corner of 5883. Whenon the waiting for message screen, if it flickers when pressing * key, it isseeing the signal from and keypad and is processing the request. If the LED comes on for 1sec then turns off, something is wrong. Can try deleting any keypads from receiver and tryto learn again.
| 
